E-6000 Glue for Tillandsia
Stick your tillandsia wherever your heart desires! This powerhouse adhesive bonds your air plants securely to driftwood, cork bark, plant frames, and beyond. Waterproof and built to last, it keeps your botanical displays intact through watering and humidity without breaking a sweat. We recommend using gloves when working with E-6000.
E6000 is formulated to meet high performance industrial requirements. The self-leveling formula forms a powerful bond with most any material and will remain flexible once cured. E6000 Industrial will handle just about any project DIYers or PROs throw at it!
- Tough – Stronger and 30X more flex than Polyurethane!
- Chemical resistant – safe for applications exposed to dilute acids and dilute caustics
- Waterproof
- Washer/Dryer safe
- Paintable – paint to match surrounding area to make UV-resistant
- Temperature resistant – unaffected by extreme heat or cold once cured
- Flexible – excellent for bonding items subject to vibration
WARNING: This product can expose you to chemicals including toluene which is known to the state of California to cause birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
Follow these step-by-step directions when using E6000:
Read directions and test small area before use.
- Surface should be clean, dry and free of dirt. For best results, lightly roughen surface before use.
- TUBE: Puncture inner seal using pointer cap (if tube has a foil seal). CARTRIDGE: Trim end of nozzle. Puncture inner seal. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from -40 to 180 °F (-40 to 82 °C) intermittently.
- Apply directly to surfaces to be bonded or repaired.
- Allow 24 hours for curing–Maximum bond strength may not be reached for up to 72 hours.
- TUBE: For future easy cap removal, apply a thin coat of petroleum jelly to the threads of the tube before replacing the cap. CARTRIDGE: For prolonged storage after opening, cover or plug the opening of the nozzle.
- Clean uncured adhesive with acetone or citrus-based solvents.
Product is paintable and immediately resistant to precipitation upon application.
Note: May damage finished surfaces. Avoid such contact until completely dry. Not recommended for use on polystyrene, polyethylene, polypropylene, Styrofoam™ or paper products.
Original: $3.00
-65%$3.00
$1.05Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Stick your tillandsia wherever your heart desires! This powerhouse adhesive bonds your air plants securely to driftwood, cork bark, plant frames, and beyond. Waterproof and built to last, it keeps your botanical displays intact through watering and humidity without breaking a sweat. We recommend using gloves when working with E-6000.
E6000 is formulated to meet high performance industrial requirements. The self-leveling formula forms a powerful bond with most any material and will remain flexible once cured. E6000 Industrial will handle just about any project DIYers or PROs throw at it!
- Tough – Stronger and 30X more flex than Polyurethane!
- Chemical resistant – safe for applications exposed to dilute acids and dilute caustics
- Waterproof
- Washer/Dryer safe
- Paintable – paint to match surrounding area to make UV-resistant
- Temperature resistant – unaffected by extreme heat or cold once cured
- Flexible – excellent for bonding items subject to vibration
WARNING: This product can expose you to chemicals including toluene which is known to the state of California to cause birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov.
Follow these step-by-step directions when using E6000:
Read directions and test small area before use.
- Surface should be clean, dry and free of dirt. For best results, lightly roughen surface before use.
- TUBE: Puncture inner seal using pointer cap (if tube has a foil seal). CARTRIDGE: Trim end of nozzle. Puncture inner seal. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from -40 to 180 °F (-40 to 82 °C) intermittently.
- Apply directly to surfaces to be bonded or repaired.
- Allow 24 hours for curing–Maximum bond strength may not be reached for up to 72 hours.
- TUBE: For future easy cap removal, apply a thin coat of petroleum jelly to the threads of the tube before replacing the cap. CARTRIDGE: For prolonged storage after opening, cover or plug the opening of the nozzle.
- Clean uncured adhesive with acetone or citrus-based solvents.
Product is paintable and immediately resistant to precipitation upon application.
Note: May damage finished surfaces. Avoid such contact until completely dry. Not recommended for use on polystyrene, polyethylene, polypropylene, Styrofoam™ or paper products.
